Stemco Moisture Ejector Manuel d'utilisateur télécharger pdf

Moisture Ejector Assembly Instructions

• Use bench vice and chain or crescent wrenches to disassemble and assemble moisture ejector.

• Remove caps from both ends and disassemble the interior components, taking care to note the location of

each part.

• Prior to assembly, carefully wipe away dirt or foreign matter from inside of both caps and the barrel and seats of the body.

Lightly grease the barrel and seats with the moly grease provided in the rebuild kit.

• Place large rubber piston no.1 on the spacer bolt no.2 with vendor name toward the hex head. Next, assemble curved washer

no. 3; stem; and spring no. 4 with the small end seated on the curved washer, on the spacer bolt. Fill outer edge of the large

rubber piston with grease prior to inserting assembly into the barrel of body

• Place exhaust valve so that it slips over the collar of the stem, and small rubber piston no. 5 with the concave side toward the

exhaust valve. Then place flat washer no. 6, with the slightly rounded outer edge next to the top of the piston, fill the exposed

threads on the spacer bolt with grease and install stop nut no. 7. Torque the stop nut to 45-50 inch pounds.

• Lightly grease the threads on each end of body, outer edge of the small rubber piston, and inside surface of the outlet cap.

Install inlet and outlet caps, making sure the blue inlet cap is placed on the end with the large piston, and tighten.

Preventive Maintenance

To assure proper operation and long life of your STEMCO Moisture Ejector, the compartment on the blue actuating end of the unit

should be cleaned at least once in the fall of the year.

This is accomplished by simply removing the actuating air line fitting (blue end) and “blowing-out” with an air hose and nozzle,

or removing the blue actuating end cap and wiping it out.

Printed in the USA

Part No. 09-930-2125

Hudson 10-536 • 2/09

STEMCO - USA

P.O. Box 1989 • Longview, TX 75606-1989

(903) 758-9981

• 1-800-527-8492 • FAX: 1-800-874-4297

www.stemco.com

STEMCO - Canada

5900 Ambler Drive, Units 4 & 5 • Mississauga, ON L4W 2N3

(905) 206-9922

• 877-232-9111 • FAX: 877-244-4555

ISO/TS 16949

STEMCO and Pro-Torq are registered trademarks of STEMCO LP

Replacement Parts

*NOTE: Only the numbered

parts

(1-7) shown at left are

in Repair Kit No. 900-1080.

The complete assembly is

shown to assist in proper

re-assembly.

MoistEjector InstallR2:MoistEjector Install-2002 2/6/09 9:03 AM Page 1

Replacement Parts 1

Résumé du contenu

Page 1 - Replacement Parts

Moisture Ejector Assembly Instructions• Use bench vice and chain or crescent wrenches to disassemble and assemble moisture ejector.• Remove caps from

Plus de documents pour Pour la voiture Stemco Moisture Ejector

Voir le document Stemco Moisture Ejector Manuel d'utilisateur

Stemco Moisture Ejector Manuel d'utilisateur (2 pages)

Commentaires sur ces manuels

Pas de commentaire

Stemco Moisture Ejector Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Stemco Moisture Ejector. STEMCO Moisture Ejector User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Pour la voiture Stemco Moisture Ejector

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Stemco Moisture Ejector